Definitive guide

    Thorough Examination & Test (TET): the complete 2026 guide

    This guide covers the Thorough Examination in the UK from every angle: what it is, which equipment is covered, statutory frequencies under LOLER, PUWER, PSSR and Work at Height, and who has the competence to carry it out. The goal: secure your compliance, avoid HSE enforcement and automate the whole cycle with dedicated TET software.

    What is a Thorough Examination?

    A Thorough Examination is a statutory inspection required by UK regulations (LOLER 1998 for lifting equipment, PSSR 2000 for pressure systems, PUWER 1998 for work equipment, PPE at Work Regs 2022 for Category III PPE, Work at Height Regs 2005 for fall protection). Its purpose is to verify the condition of the asset, its continued conformity and the effectiveness of its safety devices. It does not replace preventive maintenance, nor a post-modification examination — it records, it does not repair.

    Every Thorough Examination results in a written report given to the duty holder, retained in the digital H&S register, and enforceable in the event of an HSE audit, personal injury claim or principal-contractor review. The duty to have the examination carried out sits with the duty holder — even when the inspection is outsourced.

    Which equipment must be thoroughly examined?

    Lifting equipment and lifting accessories

    Tower cranes, mobile cranes, overhead travelling cranes, hoists, winches, forklift trucks (FLTs), telehandlers, MEWPs (cherry pickers, scissor lifts), suspended access equipment, plus lifting accessories (chain/wire-rope/textile slings, hooks, shackles, spreader beams). Governed by LOLER 1998 regulations 9 and 10 and its ACOP L113.

    Frequency: 6 months (lifting persons) — 12 months (lifting loads and accessories)

    Work equipment and machinery

    Power presses, woodworking machines, guillotines, robotic cells, automated industrial doors, self-propelled mobile equipment. PUWER 1998 requires the employer to keep the equipment in efficient working order and to have it inspected by a competent person at suitable intervals, with special attention to guards, interlocks and emergency stops (regs 5 & 6).

    Frequency: 3 to 12 months depending on the machine and its use pattern

    PPE — fall arrest (Category III)

    Full-body harnesses, lanyards, energy absorbers, mobile fall arresters, anchor points, temporary and permanent horizontal lifelines. PPE at Work Regs 2022 and Work at Height Regs 2005 require pre-use checks, detailed interim inspection and a thorough examination at least every 12 months by a competent person, plus immediate withdrawal after any arrest event.

    Frequency: 12 months — plus after any fall or change of user

    Pressure systems (PSSR)

    Steam boilers, autoclaves, air receivers, pipework, industrial gas cylinders. Pressure Systems Safety Regulations 2000 require a written scheme of examination drawn up by a competent person, followed by periodic examinations to that scheme. ACOP L122 sets out the duty holder's responsibilities.

    Frequency: 12 to 72 months per the written scheme of examination

    Industrial doors, gates and shutters

    Sectional overhead doors, sliding gates, roller shutters, rising arm barriers, communal garage doors. Machinery Supply Regulations plus HSE guidance on powered doors and gates: check safety edges, photocells, emergency stops and mechanical condition. Frequency-of-use and force-limit testing form part of the annual examination.

    Frequency: 6 months for industrial powered doors, 12 months for gates

    Racking and industrial shelving

    Pallet racking, cantilever racks, storage mezzanines, live storage. BS EN 15635 recommends visual inspection by the operator every week and an expert annual inspection by a technically competent person (a SEMA Approved Racking Inspector where appropriate) to assess stability and record impact damage.

    Frequency: 12 months by a technically competent person

    Who can carry out a Thorough Examination?

    In-house competent person appointed by the employer

    Maintenance engineers, workshop supervisors, SHEQ managers — provided they hold the practical and theoretical knowledge, have adequate measuring equipment and enough independence from production pressures. Suitable for routine internal examinations (everyday lifting, PPE, doors).

    Independent competent person

    Self-employed engineer surveyor or small specialist firm. Autonomy of judgement, controlled costs, close site relationship. A good fit for mid-sized industrial employers with a homogeneous fleet who want to outsource without going to a large body.

    Engineer surveyor from a UKAS-accredited body (SAFed member: Zurich, Allianz Engineering, HSB, Bureau Veritas, Applus+…)

    Required or strongly recommended for higher-risk items (tower crane commissioning, PSSR pressure vessel revalidation, insurance-linked inspections). Strong traceability, UKAS accreditation, and enforceability in the event of an HSE investigation, insurance claim or client audit.

    Manage Thorough Examinations with dedicated software

    Moving from spreadsheets to compliance software turns the statutory duty into an industrial process: no missed due date, no lost report, no defect left open. Cloud VGP centralises the asset register, scheduling, mobile reports, defect close-out and HSE-ready archives.

    • QR/NFC asset register — one scan to open the full asset log
    • Automatic scheduling by family and statutory frequency
    • Offline mobile reports with photos, signatures and compliant PDFs
    • Defect tracking with re-use lock until closure is documented
    • 10-year retention, one-click HSE and principal-contractor exports

    Frequently asked questions

    What is a Thorough Examination and Test (TET)?

    A Thorough Examination is a statutory inspection required by UK regulations (LOLER 1998 for lifting equipment, PSSR 2000 for pressure systems, PUWER 1998 for machinery, PPE at Work Regs 2022 for Category III PPE, Work at Height Regs 2005 for fall protection). Its purpose is to verify the good condition of the equipment, its continued conformity and the effectiveness of its safety devices. It is distinct from maintenance — it records, it does not repair. It applies to every asset listed in the applicable ACOP, and produces a written report given to the duty holder and retained for a minimum period (5 years for LOLER lifting equipment, longer for other assets).

    Which equipment must be thoroughly examined?

    The main families are: lifting equipment and lifting accessories (cranes, hoists, FLTs, MEWPs, slings, hooks), work equipment and dangerous machinery under PUWER, Category III PPE against falls from height, pressure systems under PSSR, powered industrial doors and gates, storage racking. The exact list depends on the ACOP applicable to each family. Where doubt remains (e.g. a collaborative robot or a cobot), the duty holder refers to the manufacturer's manual, the risk assessment for the task and, where necessary, to a UKAS-accredited engineer surveyor.

    What is the statutory frequency of a Thorough Examination?

    It depends on the equipment and the applicable ACOP. As a guide: 6 months for equipment used to lift persons (MEWPs, suspended platforms) and for powered industrial doors, 12 months for most load-lifting equipment, all lifting accessories, Category III fall-arrest PPE and storage racking, 3 months for certain heavy-use machinery, 12 to 72 months for pressure systems under the written scheme of examination, and 6-monthly interim for public passenger lifts under LOLER. Frequency is shortened where use is intensive, where the environment is harsh (dust, moisture, corrosion) or after an incident. Cloud VGP calculates due dates automatically per family and site.

    Who can perform a Thorough Examination?

    It must be carried out by a competent person as defined in HSE guidance INDG422 and the relevant ACOPs. That may be an in-house appointed person with adequate training, an independent competent person, or an engineer surveyor from a UKAS-accredited body (a SAFed member such as Zurich, Allianz Engineering, HSB, Bureau Veritas or Applus+). Choice depends on risk, complexity and, in some cases, on a specific requirement — for instance PSSR revalidation of a pressure vessel typically requires a UKAS-accredited body. In every case, the person must hold the practical and theoretical knowledge, appropriate measuring equipment and enough independence from the user. The competent person carries professional liability for the report.

    What must a compliant Thorough Examination report contain?

    The report identifies the equipment (make, model, serial number, date brought into service, SWL/WLL), states the statutory reference of the examination performed, lists the points examined, records measurements (proof-load tests, safety-device tests), any defects graded by severity (existing, imminent or becoming so within a defined period), recommended dates by which defects must be rectified, the identity and competence of the person carrying out the examination, their signature and the date. Under LOLER reg 10 it must be given to the duty holder as soon as is practicable and, for defects becoming imminent, a copy sent to the enforcing authority (HSE or Local Authority). Digital records accessed by QR code speed up HSE and principal-contractor audits.

    What is the difference between a TET, preventive maintenance and post-modification examination?

    A Thorough Examination is a periodic statutory inspection that records the state of the equipment and the effectiveness of its safety devices. Preventive maintenance is a scheduled technical operation aimed at keeping the equipment in efficient working order (lubrication, changing wear parts, adjustments). A post-modification examination is a one-off check required after a significant change, major repair, accident or extended out-of-service period (LOLER reg 9(3), PUWER reg 6). The three cycles are complementary and must be recorded separately: a compliance platform separates them and triggers a fresh examination the moment a modification or incident is logged.

    What is the risk of not carrying out statutory examinations?

    An out-of-date Thorough Examination exposes the duty holder to cumulative risk. Under the Health and Safety at Work Act 1974 s.33, fines are unlimited and directors can face up to 2 years' imprisonment. The Sentencing Council guidelines set penalties by turnover: a Category A high-culpability breach at a large organisation can exceed £10m. Civil liability follows quickly through personal injury claims. The HSE can serve improvement or prohibition notices requiring immediate withdrawal of the equipment. Insurance cover for engineering breakdown or public liability may be void. And principal contractors in construction, industry and logistics almost always require Thorough Examination reports as a condition of access.

    How does compliance software simplify Thorough Examinations?

    It centralises the asset register, calculates statutory due dates by family, schedules campaigns automatically, lets in-house and external competent persons complete reports on mobile (offline included) with photos and signatures, and tracks defects to closure. Cloud VGP adds QR/NFC tagging to pull up an asset's full history in one scan, tamper-evident 10-year archives, one-click HSE-ready PDF export, multi-channel alerts, a multi-site dashboard and structured invoicing for external competent persons. From £0.36 per asset per month.